I had a Condo that was on concrete slab. All we did was put a vapor barrier down and then I installed Pergo flooring. There have been no problems at all.
Check the humidity level of basement slab concrete: Once the concrete has had time to cure, check humidity with a moisture meter, and if it is 4.5% or higher, the slab might be unsuitable for laminate, even with a vapor barrier.
I am rebuilding my basement floor after a flood with a sub-floor with 2×3s floor is too uneven to install laminate directly on concrete and since no vapour barrier was put under the concrete, I want to know if putting a 6mil plastic vapour barrier directly on the concrete will do any harm.
2. Install the floor underlayment. Make sure the edges don't overlap, and tape the pieces together to prevent them from shifting. Create an expansion gap between the underlayment and the walls by using spacers. If you're placing a laminate floor on top of a concrete slab, apply a polyethylene plastic vapor barrier before installing the underlayment. 3.
Once the flooring is in place, install or reinstall your baseboards and moldings, making sure you nail them to the wall into a wall stud. Use a hammer and finishing nails, or a brad nailer. This will cover the 1/4-inch gap that was left around the perimeter of the room. Keep in mind that most laminate floors are floating floors.
Before you install laminate flooring over concrete, you must thoroughly clean your concrete subfloor. First, pull up any flooring materials already there. If you plan to reuse any floor padding, youll need to pull it up very carefully to avoid damage.
Lay the laminate, the first roll of floor boards go against your starting wall, groove side towards the wall. If you do need to cut the first row of boards to width, be sure that you cut off the groove side and place the cut side on the wall.
Learning Center / Flooring / Bamboo Flooring / The floor was glued to the concrete slab. Should I have been advised yo install a barrier or to consider other type of flooring for our home which is in a low-lying area? Used glue to put down my bamboo flooring but am have a hard time getting the glue off the floor, any indeas. Juliet
Before you install any flooring material over a concrete slab, it is important to inspect the slab for defects. Dips, bulges and cracks occur frequently as concrete cures and ages.
From this video you'll learn about how to install laminate flooring on concrete. Installing laminate flooring on concrete you should choose the right underlayment and think about water protection
Before installing laminate flooring on a new or existing concrete slab, test the slab with a moisture meter to be sure it has no more than a 4.5% moisture reading.
Place the laminate flooring on the concrete slab in the room where it is to be installed. This will help to acclimate the flooring to the room temperatures and humidity. Leave the flooring in the room for three days before installation.
For a concrete subfloor, you should install the plank with the sight lines of the floor. Typical sight lines run parallel to the longest wall, but each home is different. Measure and mark the center of all four walls at floor level.
Floor leveling: - Concrete Mixer for barrel How to Install Laminate Flooring and other Floating Floors Like a How To Level Concrete Subfloor: Preparation for Laminate or Hardwood floor
Consider using laminate flooring instead. Laminate can capture the look of wood at a fraction of the cost. This material consists of a wood fiber core with a paper top, all covered by a final resinous seal coat.
Your subfloor could be a concrete slab or it could be wood boards. If you are laying a floating hardwood floor then you can pretty much ignore it as most floating floors can lay over ceramic, tile or other flooring. You will also need to get a moisture measurement before you lay an underlayment because although most laminate floors can handle more moisture than most floor, high moisture
Insert the tongue of the second-row plank into the groove of the first-row plank at a slight angle until the laminate edges meet. Next, rotate down until the joints lock Image 1 . For the next plank, join the short end of the plank first Image 2 . DIY experts show how to install underlayment and laminate flooring to get beautiful results